Printing is only half of a banner. Finishing — the hems, grommets, pockets and edges added after printing — decides how the banner hangs, how long it lasts and which parts of the artwork stay visible. Choosing the finish before you design saves you from logos punched by grommets or headlines folded into a pocket. Here's what each common option is and how it affects your file.
Hems
A hem folds the edge of the banner back on itself and secures it, usually by heat welding (for vinyl) or sewing (for fabric or heavy-duty jobs). Hems reinforce the edges so grommets have something solid to hold and so the edge doesn't fray or tear in the wind.
Effect on artwork: the folded part is on the back, but the fold line sits slightly inside the edge and the doubled material can show a faint line. Keep text and logos at least 1 to 2 in from the edge. Most shops hem vinyl banners by default.
Grommets
Grommets are metal rings (usually brass or nickel-plated) pressed through the hemmed edge so the banner can be tied, hooked or zip-tied in place. They are the standard finish for outdoor vinyl banners.
- Placement: at every corner, then spaced along the edges. Spacing of about every 2 ft is common; some shops go to every 12 to 18 in for windy locations or heavy banners.
- Edges: all four sides, top and bottom only, or top only, depending on how the banner hangs.
- Effect on artwork: grommets sit inside the hem, roughly half an inch to an inch from the edge. Nothing important should be there.
Tell the shop how you plan to hang the banner — a fence, a building, a frame — and they can recommend spacing.
Pole pockets
A pole pocket is a sleeve sewn or welded along an edge, usually the top and sometimes the bottom, so a pole, pipe or rod can slide through. Pole pockets are used for banners on stands, light-pole brackets and many step-and-repeat backdrops.
- Size: pockets are described by their opening, such as 2, 3 or 4 in. The right size depends on the diameter of the pole — tell the shop what hardware you have.
- Top only or top and bottom: a bottom pocket with a weighted rod keeps a banner hanging flat and stops it from flapping.
- Effect on artwork: the pocket area folds back. Depending on the shop, the pocket material is either added outside your artwork or taken from inside it. Ask which, and keep critical content out of that band either way. The Logo Wall Builder uses a 2 in pole pocket option for stand-mounted walls, with the pocket material added outside the file by the shop.
Wind slits and mesh
Large solid banners outdoors act like sails. Two common ways to reduce wind load:
- Wind slits are small half-moon cuts in the banner. They help a little, but they cut through the artwork and the effect is limited.
- Mesh vinyl has tiny perforations across the whole material that let air pass through. It's the better choice for fences, scaffolding and building wraps. The image is slightly less saturated up close but looks solid from a distance.
Wrap-around for tension and Velcro frames
Some backdrops stretch over a frame and attach on the back with Velcro or similar fasteners. The graphic must be larger than the frame face so it wraps around the sides. Common wrap depths are 2 or 3 in on the sides, sometimes on all four edges. In the file, the wrap area should carry background only, with fold lines measured in from the edges. In the Logo Wall Builder, turning on wrap bleed reserves that wrap inside the size you order.
Silicone edge graphics (SEG)
SEG is a fabric finishing method common in trade-show displays and lightboxes. A thin silicone strip is sewn around the edge of a dye-sublimated fabric graphic and pushed into a channel in an aluminum frame, pulling the fabric tight. The shop will provide a template with the exact size and the margin hidden in the channel.
Hanging hardware
Other finishing options you may see:
- Rope or cable in the hem for very long banners that need strength along the edge.
- D-rings or webbing sewn to corners for heavy-duty outdoor use.
- Adhesive tape or grommet-free edges for indoor banners mounted to a wall or in a frame.
- Keder edges on large tension systems.
Choosing a finish
- Outdoor fence or building banner: hem and grommets, mesh if it's windy.
- Banner on a pole stand or step-and-repeat stand: pole pockets.
- Backdrop on a tension or Velcro frame: wrap-around.
- Trade-show frame or lightbox: SEG fabric.
- Retractable banner: no hem or grommets; the graphic attaches to the rail and the base cassette. See Retractable banner file setup.
Setting up the file around finishing
- Decide on the finish before designing.
- Ask whether hems, pockets or wraps are added outside the file or taken from inside it.
- Keep text and logos well clear of edges — 1 to 2 in for hemmed and grommeted banners, more for pockets and wraps.
- Run the background to the edge (and into bleed) so finishing never shows a white line.
- Note the finish in your order and, if helpful, in the file name.
For bleed and margin basics, see Bleed, safe zones and DPI for large format.