Quick length and print helpers for banners, panels, and general shop work: convert decimals and fractions, switch units, split a total size into panels, and figure pixel size at a chosen DPI.
On the first tab, type a decimal like 10.3 or a fraction like 10 5/16. Pick how fine to round (16ths, 32nds, etc.). The default is 16ths. Results show the fraction, decimal inches, and the same length in other units. Use copy to grab a value.
Open the Length Converter tab. Enter a value, choose From and To units, and set the rounding. The default round-to is 16ths (1/16"). The main answer updates live, and All units lists every conversion. Tap ⇄ to swap From/To. Feet-inches can be typed as 18' 10 1/2".
Ft-In → Inches turns feet-inches into total inches. Panel splitter takes overall length, panel size, and overlap, then tells you how many panels and cut sizes. Size @ DPI turns width × height × DPI into pixel dimensions for print files.
Yes. The layout adapts to smaller screens. Use Light/Dark in the top right if you want a brighter look.
No. Everything runs in your browser. Nothing is uploaded or saved on a server.
Large-format print work is full of awkward measurements. A customer gives you a wall as 18 feet 10½ inches, the design file is in decimal inches, the printer's roll is 54 inches wide and the shop's RIP wants pixel dimensions. This page puts the conversions you need for that work in one place. Everything runs in your browser — there is nothing to install and nothing is uploaded.
Tape measures in US shops are marked in fractions, while design software works in decimals. Type either form into the first tab — 10.3 or 10 5/16 — and the result panel shows both, plus the same length in millimeters, centimeters, meters, feet, feet-and-inches and yards.
The Round to setting controls how fine the fraction is. Sixteenths are the default because most tape measures are marked to 1/16 in. Choose 32nds or 64ths for precise machine work, or halves and quarters for rough sizes. The Rounding error line shows how far the fraction is from the exact decimal. For example, 10.3 in rounds to 10 5/16 in, which is 10.3125 in — an error of +0.0125 in, far smaller than any cut on a banner.
The second tab converts between inches, fractional inches, feet, feet-and-inches, yards, millimeters, centimeters, meters, points and picas. Enter a value, choose From and To, and the large answer updates as you type. The ⇄ button swaps the direction. Below the answer, All units lists the same length in every unit, and the formula line shows the multiplier used, so you can check the math or repeat it by hand.
Feet-and-inches can be typed the way people write them: 18' 10 1/2", 18 10.5 or 18ft 10in all mean 226.5 inches. Points and picas are included because layout software often uses them: there are 72 points or 6 picas in an inch. The Reference table builds a quick lookup chart, such as feet to inches for common sizes from 1 to 240.
Ft-In → Inches turns a feet-and-inches measurement into total inches, decimal inches and decimal feet in one step — handy when a site measurement has to become a document size.
Panel splitter is for anything too wide for one piece of material: wall graphics, wallpaper-style murals, long fence banners and large window films. Enter the total length, the panel width your material allows and the overlap you want between panels. The tool tells you how many panels you need, the leftover width of the last panel, and the cut sizes. An end panel is cut at the panel width plus one overlap; a middle panel overlaps on both sides, so it is cut at the panel width plus two overlaps.
For example, a 600 in wall with 48 in panels and 1 in overlap needs 13 panels. Twelve full panels cover 576 in, leaving 24 in for the last one. Middle panels are cut at 50 in and end panels at 49 in. Overlaps let installers hide small variations in walls and material, and many shops use 0.5 to 1 in for wall graphics. Always confirm the overlap your installer prefers.
Size @ DPI works out the pixel dimensions of a print file. Enter the width and height in inches and the resolution, and it returns the size in pixels, the size in feet-and-inches and the total megapixels. A 33 × 80 in retractable banner at 150 DPI is 4,950 × 12,000 pixels; at 100 DPI it is 3,300 × 8,000. The default example, a 226 × 600 in wall at 20 DPI, shows how low resolution can go on very large graphics viewed from a distance: about 4,520 × 12,000 pixels.
Resolution for large format depends on viewing distance. Brochures read at arm's length need about 300 pixels per inch, but banners, backdrops and signs are seen from several feet away. As a general guide, 100–150 PPI at final size works for banners, retractables and trade-show graphics that people walk up to, while building wraps and billboards seen from far away can go much lower. If a file falls short, a bigger original or a vector version is the real fix — enlarging pixels in software doesn't add detail. The guide to bleed, safe zones and DPI for large format explains this in more depth.
If you need a finished print file rather than a measurement, the Templates page has builders for step-and-repeat logo walls, retractable banner stands and table throws, each producing a CMYK PDF at the exact size. For background, read the guides on banner and backdrop sizing, grommets, pole pockets and hems, and PDF export settings for print shops.